ESP - v pravé zatáčce blokne kolo a blikne žárovka na př.des
Moderátoři: šulda, Moderátoři
Kdyz tu rozebirate esp a zakladni nastaveni tak poradte jak na nej.Kolega delal z.nastaveni na octe I podle vypisu z visu a nezdarilo se.Nechtelo to vzit login ktery podle visu je 40168 a kanal 060 mu to vubec nenaslo...Delal to pomoci diag ts pro.Vag bohuzel nemame k dispozici ale klapky a podobne veci to nastavi bez problemu...Tak netusim co delal spatne nebo co se podelalo...
OIII 1.4 TSI 240 000km
FI HTP LPG 340 000km
FI HTP LPG 340 000km
Tome co jsem zatím vyčetl je tady v tom odkazu, bohužel tam nejsou detaily jaký login a podobně, ale je tam zmínka že to základní nastavení se musí dělat u všech součástí systému ESP, jako duosenzor, volant, snímač tlaku a podobně.
http://www.skodaoctavia.cz/skoda-octavia/montaz-esp
http://www.skodaoctavia.cz/skoda-octavia/montaz-esp
T-ROC 2.0 TSI 4Motion
Golf IV 1.9 TDi ASZ
_________________
favorit 136 L
felicia 1.3 (1.4) MPi
Golf IV 1.9 TDi ASZ
_________________
favorit 136 L
felicia 1.3 (1.4) MPi
Co tohle ?
Spojit se s řídící jednotkou,zadat login 40168,zvolit základní natavení,pak ukončit komunikaci. Kontrolky abs a esp budou nyní svítit.
Prudce sešlápnout brzdový pedál,kontrolka abs by měla zhasnout. Poté se pomalu rozjet,prudce zatočit doprava a pak doleva,kontrolka esp by měla zhasnout. To je vše. Nejdříve je však třeba vymazat závady v paměti jednotky.Pokud chyby nelze vymazat,není základní nastavení možné. Mimo závady"jizdní test aktivován".
T-ROC 2.0 TSI 4Motion
Golf IV 1.9 TDi ASZ
_________________
favorit 136 L
felicia 1.3 (1.4) MPi
Golf IV 1.9 TDi ASZ
_________________
favorit 136 L
felicia 1.3 (1.4) MPi
postup je jiný...
Adaptation
Basic Setting
Sensor for Steering Angle (G85)
Prerequisites:
Start the vehicle.
Turn the steering wheel one turn to the right and one turn to the left.
Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
Ensure that the steering wheel is not moved again.
Keep the engine running and do not switch off the ignition.
System voltage at least 12.0 V.
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 °.
[Done, Go Back]
[Coding-II - 11]
OR (if Coding-II is not available)
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
[Close Controller, Go Back - 06]
Adaptation
Basic Setting
Sensor for Steering Angle (G85)
Prerequisites:
Start the vehicle.
Turn the steering wheel one turn to the right and one turn to the left.
Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
Ensure that the steering wheel is not moved again.
Keep the engine running and do not switch off the ignition.
System voltage at least 12.0 V.
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 °.
[Done, Go Back]
[Coding-II - 11]
OR (if Coding-II is not available)
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
[Close Controller, Go Back - 06]