DP forum

vag 607 nejde vyčíst cela ser. pamět jen ty km (asi je to dělany nějakym makro)

Hm,kdyz zadam funkci 26 tak mi to napise Elektricke ovladani strechy a kdyz to dam pres 01 tak mi uz 26 nejde zadat.Tak nevim Seat Toledo 1,9tdi 1999

Obelisek píše:Hm,kdyz zadam funkci 26 tak mi to napise Elektricke ovladani strechy a kdyz to dam pres 01 tak mi uz 26 nejde zadat.Tak nevim Seat Toledo 1,9tdi 1999

mne tak isto

Myslím kdyby to šlo číst klasickým VAG tak by prodejci SW na přizpůsobení
starší jednotky (číst PIN IMMO) asi moc neprodaly,ale rád se o tom dozvím více.

kevino píše:

Obelisek píše:Hm,kdyz zadam funkci 26 tak mi to napise Elektricke ovladani strechy a kdyz to dam pres 01 tak mi uz 26 nejde zadat.Tak nevim Seat Toledo 1,9tdi 1999

mne tak isto

Tu funkci 26 zadávaš ve VDS/VDC-PRO.
Ve Vag 607 je to v"Automatické příkazy"

Ale takove zadani ve Vag 1552 asi nenastavim,nebo nevim jak

zdravim.hned zitra to vyzkousim.koupil jsem octavii a ta ma urcite stoceny km a moc me zajima o kolik.mam ale vagcom 704.pujde to taky?a jeste mam ho anglicky tak jak se to asi tak jmenuje po anglicky?diky

vagus píše:

Obelisek píše:A jak se da precist Vagem 1551? Diky

funkce "26" - serial eeprom reading.

S 304 sa to neda nejak vycitat?Myslim ten skutocny stav km.

Kvako28 píše:

vagus píše:

Obelisek píše:A jak se da precist Vagem 1551? Diky

funkce "26" - serial eeprom reading.

S 304 sa to neda nejak vycitat?Myslim ten skutocny stav km.

nie neda

mate niekto diagRu v anglictine ? ja mam len nemcinu

palikx píše:zdravim.hned zitra to vyzkousim.koupil jsem octavii a ta ma urcite stoceny km a moc me zajima o kolik.mam ale vagcom 704.pujde to taky?a jeste mam ho anglicky tak jak se to asi tak jmenuje po anglicky?diky

Ma to tak isto ako 607 a km vycitat ide,

supervagem u podporovaných jednotek ,

Use the following procedure to reprogram the module

1. start vdc
2. connect to central convenience (46)
3. start login procedure (11)
4. use the code 19283
5. read serial eeprom (26)

Find the list of known values further down this post. Write down the original values at and continue.

6. write serial eeprom (27)

Enter the memory address and value mentioned in the list down below.
Do this for all addresses mentioned

7. end output (06)

Now exit your car and lock it. When you now open your car with the keyfob and hold the button the windows should start to roll down and stop when you lift your finger.

This works for all VW/Seat/Skoda cars that use the same type control module. Passat B5, B5.5, Golf Mk IV, Seat Leon, Jetta, Bora...

The following codes have been collected on different boards in Germany for the listed modules:

1J0 959 799 AH (any index) and 1J0 959 799 S 03B

Memory Address / old value / new value
04283 / 8 / 2
04289 / 8 / 2
08628 / 242 / 246 driver side front window
12724 / 250 / 254 passenger side front window
16820 / 250 / 254 driver side rear window
20916 / 242 / 246 passenger side rear window


1J0 959 799 J 00E

Memory Address / old value / new value
04286 / 8 / 2
04291 / 8 / 2
04296 / 8 / 2
08628 / 242 / 246 driver side front window
12724 / 250 / 254 passenger side front window
16820 / 250 / 254 driver side rear window
20916 / 242 / 246 passenger side rear window


1C0 959 799 A (any index) and 1C0 959 799 B (any index) for Variant/Wagon

Memory Address / old value / new value
04361 / 75 / 67
04362 / 75 / 67
04363 / 75 / 67


1C0 959 799 A (any index) and 1C0 959 799 B (any index) for Limousine/Sedan

Memory Address / old value / new value
04361 / 74 / 66
04362 / 74 / 66
04363 / 74 / 66

Vseznalek píše:Zdravám nemam vagcom 607 kde jsme četl že umí načíst opravdový stav, lze to udelat i s něčím jiným ? abych nemusel kupovat novej kabel
Díky

Ak máš KKL com, tak VAG Comander 1,2. Funguje pre EDC15...
Napíš SZ

Mireck píše:Use the following procedure to reprogram the module

1. start vdc
2. connect to central convenience (46)
3. start login procedure (11)
4. use the code 19283
5. read serial eeprom (26)

Find the list of known values further down this post. Write down the original values at and continue.

6. write serial eeprom (27)

Enter the memory address and value mentioned in the list down below.
Do this for all addresses mentioned

7. end output (06)

Now exit your car and lock it. When you now open your car with the keyfob and hold the button the windows should start to roll down and stop when you lift your finger.

This works for all VW/Seat/Skoda cars that use the same type control module. Passat B5, B5.5, Golf Mk IV, Seat Leon, Jetta, Bora...

The following codes have been collected on different boards in Germany for the listed modules:

1J0 959 799 AH (any index) and 1J0 959 799 S 03B

Memory Address / old value / new value
04283 / 8 / 2
04289 / 8 / 2
08628 / 242 / 246 driver side front window
12724 / 250 / 254 passenger side front window
16820 / 250 / 254 driver side rear window
20916 / 242 / 246 passenger side rear window


1J0 959 799 J 00E

Memory Address / old value / new value
04286 / 8 / 2
04291 / 8 / 2
04296 / 8 / 2
08628 / 242 / 246 driver side front window
12724 / 250 / 254 passenger side front window
16820 / 250 / 254 driver side rear window
20916 / 242 / 246 passenger side rear window


1C0 959 799 A (any index) and 1C0 959 799 B (any index) for Variant/Wagon

Memory Address / old value / new value
04361 / 75 / 67
04362 / 75 / 67
04363 / 75 / 67


1C0 959 799 A (any index) and 1C0 959 799 B (any index) for Limousine/Sedan

Memory Address / old value / new value
04361 / 74 / 66
04362 / 74 / 66
04363 / 74 / 66

Mirecku a toto si tu co dal ? to ma daco spolocne s kilometrami ?